Welcome to the new Quick Draw Brand website. As we upload all our great products feel free to reach us at sales@quickdrawbrand.com for parts not displayed.

phone: 513-712-4844

Quick Draw Brand

Engine and Adapter - Cummins R2.8 Crate engine & Land Rover R380 Adapter Kit (300TDI)

$11,725.00
No reviews yet Write a Review
SKU:
EN-00013
Weight:
770.00 LBS
Width:
40.00 (in)
Height:
44.00 (in)
Depth:
41.00 (in)
Shipping:
Calculated at Checkout

Cummins R2.8 Turbo Diesel Engine with Land Rover R380 5 speed Manual Transmission

  • New 4 cylinder Cummins R2.8 Crate Engine  (Part#5467046)
  • Adapter works with 300 TDI Version 5 Speed
  • Bell housing bolts the transmission directly to the engine
  • Designed to work with Mopar Small Block 10.5″ 23 Spline clutch kit Part# 05029
  • Best fits 4 cylinder Defenders which were built before the 1993 floor change over
  • Engine carries a 2 year 2600 hour warranty covered thru Cummins (Buyers in USA ONLY)
  • Due to Emission regulations, engine must be installed in vehicles 1999 or older, will require VIN at purchase
  • R2.8 Engine is not supported under warranty for Buyers outside of the United States
  • Best performance with a 1.2 ratio Transfer Case
  • Kit# EN-00013

Parts included in Kit:

QTY Description Part# and Location
1 Cummins 4 Cylinder crate engine 5467046
- Complete Front-end accessory drive  
- Vacuum Pump  
- Remote fuel/ Water separator 5268019
- Remote Oil Filter 5308354
- Remote Oil Filter Manifold 5209233
- Mass Air Flow Sensor and Housing 4984760
- Engine Wiring Harness and ECM  
- Starter  
- Universal Wiring Harness  
- Throttle Pedal  
- Oil Fittings  
- J1939 Can Dash Display  
- Owners Manual  
  Installation Guide  
1 Bell Housing QDB-210147
1 Bell Housing Spacer QDB-210148
2 Bell Housing Dowel QDB-210074
1 T.O. Bearing Snout QDB-210084 (Press in Bell Spacer
1 Pivot Ball 5287452
1 Flywheel QDB-210109
1 Flywheel Insert QDB-210017
1 Clutch Fork QDB-210123
1 Clutch Fork Retainer QDB-210001
1 T.O. Bearing UTJ10021
1 Pilot Bearing QDB-210059
1 Slave Cylinder QDB-220045 (1998 Jeep .75" bore)
1 Slave Cylinder Fitting QDB-220046 (-3AN)
3 5/16-18x1.0" SHCS (Snout)
1 5/16-18x.75" Hex Head (Fork Retainer)
3 5/16 Lock Washer (Fork Retainer & Slave Cylinder)
2 5/16-18x1.25"   Hex Head (Slave Cylinder)
2 5/16 Flat Washer (Slave Cylinder)
5 M12-1.75x180mm SHCS (Bell to Trans)
1 M12-1.75x160mm SHCS (Bell to Trans)
6 M12 Flat Washer  (Bell to Trans)
12 M10-1.5x40mm  SHCS (Bell to Engine)
12 M10 SAE Flat Washer (Bell to Engine)
6 3/8-16x1.0" Hex Head (Clutch)
6 3/8 Lock Washer (Clutch)

Dimensions:

Length from Harmonic Balancer to rear face of Transmission: 48.5"

Weight:  685lbs